Tenergy LiPo 11.1v 1000mAh 3s 20C Tri-panel Pack Battery
[K15G00][11916 / 31600 / LIPO11.1V1000N]Free Shipping for orders over $179 No Coupon neededNew to airsoft? Here are some safety tips for airsoft guns that we recommend following.
Please Note: Lithium Polymer batteries MUST be charged with a Lithium Polymer Balance Charger!
Lithium Polymer batteries are the newest available batteries for airsoft and other hobby toys. They are designed as a light weight, high output power source. This 11.1v Li-Po battery can deliver more power than 12v Ni-MH large type battery with only half of the size and a third of the battery cells.
While Tenergy batteries are great, I Power LiPO batteries are now available with more mAh for an affordable price! Check out I Power LiPO batteries by click HERE.
Specifications:
Manufacturer: Tenergy
Voltage: 11.1v
Milliampere Hours: 1000mAh
Cell Type: Lithium Polymer (LiPo)
Connector Type: Mini
Recommended Fit: M4A1, AK, M14, MP5, G36
- The makers of LipoSack or its distributors or retailers assume no liability for failures to comply with these use and safety guidelines.
- By purchasing this product, the buyer assumes all risks associated with its intended use. If you cannot comply with these guidelines please return this product unused to your retailer.
1) Charge batteries in a safe area away from flammable materials and only on a non-flammable surface in a vented area. Do not discharge batteries below 3 volts/cell. Doing so may result in cell damage and subsequent cell venting upon a subsequent charge.
2) Do not recharge damaged batteries. Dispose of damaged batteries in the proper manner.
3) Some Lipo chargers on the market may have technical deficiencies that may cause it to charge the battery incorrectly or at an improper rate. It is your sole responsibility to assure that the charger you purchased works properly. Always monitor the charging process to assure batteries are being charged properly. Failure to do so may result in cell damage or fire.
4) In the event of a crash, you must remove the battery from the model for observation and place in a safe open area away from flammable materials.
LipoSack Use Instructions:
1) Ensure that charger rate is properly set and polarity is correct.
2) Attach charging leads to battery.
3) Place battery in LipoSack towards the bottom.
4) Place LipoSack on non-flammable surface.
5) Route charge leads through vent at the top seam of the LipoSack.
6) Close top flap of LipoSack and press hook and loop closure fully closed.
7) Charge battery using proper charging practices.
LiPoSack Use and Safety Instructions:
Battery safety:
∑ Lithium Polymer batteries are volatile. Failure to adhere to established charging guidelines may result in fire, personal injury and damage to property if charged or used improperly.
Airsoft GI Battery Disclaimer:
Airsoft GI is not responsible for batteries that have been damaged as a result of improper operation, storage, misuse or abuse, accident or neglect, such as physical damage resulting from misuse; contact with liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or the like, extreme heat, or food; use of the battery for commercial purposes or subjecting the battery to abnormal usage conditions, or other acts which are not the fault of Airsoft GI. Make sure you understand how your battery should be used and how long it should be charged. If you have any doubt regarding the operation, charging, or storage of your battery and/or charger, ask. A charging battery should not be left unattended and should be picked up periodically while charging to check for overheating. Do not charge batteries near flammable material. For more information regarding batteries please refer to the Frequently Asked Questions or the Airsoft GI Airsoft 101 Guide.
- Specifications
- Manufacturer: Tenergy
If you have a crane stock this battery should fit. I used this battery in my kwa crane stock as well as a g&g crane stock. I have a g&p shorty stock on my m4 now so I dont need to buy tri panel batteries now but I like this battery as well as not wanting to wait for shipping im going to airsoft gi this week to get another one. If you have pre-engagement problems this battery may also be good for you because its a constant 20c discharge and doesnt jump up. I soldered this battery to deans so I cant tell you if the mini tamiya connectors were good or not since i never used them. My stubby shoots 35 rps with this battery and it stays relatively cool, even when using semi very fast.
Pros:
-fits in crane even with a mosfet
-fits in dull stocks (of course) and might fit in buffer tube
-constant 20c discharge
-quality seems pretty good
-this battery is pretty good at staying cool
-this review goes for the other tenergy 11.1 that is just like this but not a tri panel (I own one of those also)
Cons:
-comes stock on small tamiya connecors (not a con for everyone)
-even though quality is good sometimes i feel a wire may come unconnected from a cell
|
Will this be compatible with a KWA SR10?
First time buyer
2533 days ago Dave K
0
0
(I have this same question)
Staff Answer:
Yes it is. 2422 days ago 0
0
|
1 answers 1 asked |
|
Will this fit in the lvoa-c? And is it the ideal battery?
Inquiring on buying the lvoa and want to make sure to get the correct battery
2657 days ago John S
0
0
(I have this same question)
Staff Answer:
Yes, it would fit. 2410 days ago 0
0
|
1 answers 1 asked |
|
Will it fit?
Will it fit in a PTS enhanced polymer Stock?
2790 days ago Nathan B
0
0
(I have this same question)
Staff Answer:
Yes it will. 2410 days ago 0
0
|
1 answers 1 asked |
|
Will it fit?
Will this battery fit in the ASG CZ Scorpion?
3519 days ago cameron b
2
0
(I have this same question)
Staff Answer:
It hsould 3517 days ago 0
0
|
1 answers 2 asked |
|
fit
will this fit in a kwa cqr mod 2 with no mods or adapters?
3603 days ago joe m
0
0
(I have this same question)
Staff Answer:
It should 3587 days ago 0
0
|
1 answers 1 asked |
|
Is one of the sells supposed to be fatter and bulging compared to the others?
I just bought and received one of these lipos and i have never used it or even plugged it in. I was about to plug it in and i noticed the cell with the sticker on it is fatter than the others and feels like it has a liquid inside. I want to know before i plug it in because this is my first lipo and i dont want to start a fire. thank you.
3619 days ago Tammy G
0
0
(I have this same question)
Staff Answer:
Please contact our customer service department for support 3618 days ago 0
0
|
1 answers 1 asked |
|
Krytac stock
Will this fit a krytac trident SPR M4
3637 days ago Jakob R
0
0
(I have this same question)
Staff Answer:
Yes 3634 days ago 0
0
|
1 answers 1 asked |
|
How long do I charge this for?
This is the second one I have owned of this exact battery. I have no idea how long to charge it.
3826 days ago David H
0
0
(I have this same question)
Staff Answer:
You have to use a LiPo charger which will shut off when done charging 3825 days ago 0
0
|
1 answers 1 asked |
|
Where is part that connects to gun and charger?
the Tamiya and other thing
3911 days ago Domenick D
0
0
(I have this same question)
Staff Answer:
The longer piece (tamiya connector) connects the battery to the airsoft gun. The shorter piece connects the battery to any LiPO charger. 2410 days ago 0
0
the Tamiya and other thing
3911 days ago Domenick D
0
0
(I have this same question)
it could be in the stock or somewhere else (refer to the guns manual)
2702 days ago
joshua l
0
0
|
2 answers 1 asked |
|
What connecter is it
Is it a Small Tamiya Connector?
3914 days ago Joshua B
0
0
(I have this same question)
Staff Answer:
The battery should have a Small Tamiya Connector. 3914 days ago 0
0
|
1 answers 1 asked |
|
Will this Battery fit in a crane stock?
Will this battery fit in a crane stock? FMG4?
3919 days ago Preston H
0
0
(I have this same question)
Staff Answer:
This should fit in a crane stock. 3916 days ago 0
0
|
1 answers 1 asked |
|
Will this fit in the KM4 RIS stock?
I currently own the 11.1V stick variant which fits in my VFC 416 buffer tube however not in my KM4 RIS.
3931 days ago Sandor H
0
0
(I have this same question)
Staff Answer:
This should fit okay. Keep in mind that an 11.1v Lipo may void your warranty with KWA. 3930 days ago 0
0
|
1 answers 1 asked |
|
will it fit
Will this fit into the FMG4 series?
3933 days ago Jacob F
0
0
(I have this same question)
Staff Answer:
This should fit. 3930 days ago 0
0
|
1 answers 1 asked |
|
Fitting?
Will this batter fit inside the hand guards of a G&G MP5 by H&K
3952 days ago Chris M
0
0
(I have this same question)
Staff Answer:
This battery should fit. 3951 days ago 1
0
|
1 answers 1 asked |
Other Great Deals and Accessories:
Select the item from the Drop Down Menu and click add.