JG Full Metal Body for M4/M16
[X06C10][05773 / JGM-122]Free Shipping for orders over $179 No Coupon neededNew to airsoft? Here are some safety tips for airsoft guns that we recommend following.
Description:
The JG Full Metal body for M4 is exactly what you need to pump up your gun and add realism. This economic design is full metal and completely blank on the left and right side of the magazine well. This metal body is made of high quality aluminum for strength and realistic weight. Don't miss out on your opportunity to make your M4 look and feel more realistic.
Specifications:
Manufacturer: JG
Materials: Steel
Please Note:
This metal body requires a one piece metal hop up. Call the Airsoft GI Tech Department for more details.
- Specifications
- Manufacturer: JG
Best deal for the quality and price. The body has a nice look and feel as it should and no cosmetic malformations. As the other reviewer said, some cheaper magazines such plastic ones may wiggle while inserted. Problem can easily be solved with one wrap of electrical tape around the top base of the mag. Even then, there may not be complete tightness when the mag is in, even for metal ones. But as far as I can tell it does not cause feeding or shooting issues of any kind. The paint seems good because I have yet to really get any scratches on it except the ones I made while swapping the body out (my fault). Mag release is tight, switch to shooting mode may be slightly tighter. Charging handle on mine seems pretty loose and wiggly when I mess around with it but not enough to where it can fall out.
Pros:
+All as description says.
+Adds minimal/unnoticeable weight.
+Relatively resistant to light impact.
(+/-) Body seems to be a tighter fit.
Cons:
-firmness of mechanisms may vary on body.
-Lower grade mags may wiggle.
(+/-) Body seems to be a tighter fit.
Came in good condition, but my god... Is this a shoddy piece of work. Nothing on this is built to spec.
Pros:
Its metal, which is nice
Its a clean slate, can engrave if you want
..... Idk what else i can say about it beyond that.
Cons:
- Picatinny rail isn't real width
- Low quality mags don't sit at all
- Mid quality mags hardly sit, and never feed
- High quality mags sit alright. Can just be pulled out. Feeds well though
- Mag release doesn't seem to be the right size
- Buffer tube piece is too long, needed to be milled down for my stock to fit properly
- Selector switch seems shoddy too. Feels cheap.
Bought this to rebuild a TM m733, went with a jg body due to price, and the fact they seem to copy TM a bit closer than others. Asgi was even willing to price match for me, so props on the customer service! If putting this on a Marui, or other 2 piece hop-unit gun, be sure to have a 1 piece hop to use with this receiver.
Pros:
Came with body pins, mock bolt release, mag release, and a few other bits I didn't use/need.
Metal
Price
TM grip fit the lower nicely; didn't mess with motor alignment
No trades, so you could paint/stencil/engrave your own stuff there
Mag release spring is stronger/longer than stock spring
Buffer tube fit was fine
Cons:
Had to file the fins on my TM outer barrel to fit the upper; not a big deal. I used some Permatex dielectric grease to help coax them together
Mag release itself is hot garbage. Screw stripped, and the mag release bar was funky; held mags weird. Wound up using the release off the old body.
Holes for pins weren't quite right. With both body pins in, the trigger pin was off, Wound up leaving out trigger pin; probably bend a piece of 14awg solid copper wire in the hole and turn the ends to stay. Trashy, but it'll do.
Lower seemed a bit too wide for the stock marui mechbox. I wound up shimming the side opposite the selector switch with some foam.
Mockbolt from my TM couldn't clear the adjustment gear on my hop unit. Unsure if fault of the upper receiver or my hop unit. Probably could have sanded the wheel/trimmed the bolt, but I'll just run the thing with the ejection port closed.
|
Will this fit | 0 answers 1 asked |
|
would this fit g&G
would it fit G&G R8-L Gearbox and everything internally with tht gun and the free float RIS system?
3546 days ago alex b
0
0
(I have this same question)
Staff Answer:
It may fit but the body pins may or may not align properly and some modification may be required. 3526 days ago 0
0
|
1 answers 1 asked |
|
Is it fit for Tokyo Marui Knight's M4 SR-16? | 0 answers 1 asked |
|
Will this work with G&G Blowback Gearbox if blowback is diabled?
I have switched my cylinder and disabled the blowback feature but am looking for a full metal body. I know the charging handle mounts differently with the G&Gs but if it no longer functions and the charging handle were removed, could this JG body and the charging handle it comes with work? Thank you!
3550 days ago Bryan S
0
0
(I have this same question)
Staff Answer:
No 3550 days ago 0
0
|
1 answers 1 asked |
|
will this fit a gi g4
i have a gi custom g4 and whant a metal body to replace the polymer one
3600 days ago gregory D
0
0
(I have this same question)
Staff Answer:
The JG metal body is not compatible with G&G blowback gearboxes. 3591 days ago 0
0
|
1 answers 1 asked |
|
How much would it cost for an employee of Gi to install this for me?
The gun that I have is currently out of stock, but i have a JG M4-A1 with functional bolt catch (polymer body). would that be compatible with this metal body? Is GI able to install this Metal body and replace my plastic one? how much would it cost?
3606 days ago Barton P
0
0
(I have this same question)
Staff Answer:
Our tech work fee is a flat $45 for installation, and any additional parts necessary would be an additional cost. 3604 days ago 0
0
|
1 answers 1 asked |
|
hop up
is a metal hop up required for this body or can i use a plastic one
3609 days ago Timothy A
0
0
(I have this same question)
Staff Answer:
Both should work 3607 days ago 0
0
|
1 answers 1 asked |
|
what is included
what is exactly included in this kit
is the dust cover, fire selector, and spring depressor button included
3609 days ago Timothy A
0
0
(I have this same question)
Staff Answer:
No additional components are included. 3591 days ago 0
0
|
1 answers 1 asked |
|
JG614? | 0 answers 1 asked |
|
RIS? | 0 answers 1 asked |
|
parts
Does this come with parts such as charging handle, magazine release, ect
3949 days ago Morgan S
0
0
(I have this same question)
Staff Answer:
This is strictly the body, and does not come with parts not pictured. 3949 days ago 0
0
|
1 answers 1 asked |