Burst Wizard 3 Small Tamiya Connector Mosfet
[S04J06][17618]
OUT OF STOCK
Free Shipping for orders over $179 No Coupon neededNew to airsoft? Here are some safety tips for airsoft guns that we recommend following.
The Burst Wizard King Kong Super 3 ( BWKKS3 ) MOSFET for AEG allows the user to easily and nearly seamlessly flip between burst firing mode into pure MOSFET mode. This plug-and-play MOSFET system contains a large number of features but even more programmable features become available when hardwired to an AEG. With almost every airsoft field, there is some sort of firing limitation, which is more easily and economically accomplished by installing the BWKKS3 into any AEG. The Adaptive Smart Resettable Fuse is a proprietary feature that protects valuable AEGs in the event that the gearbox or motor is locks up or there is a short in the wiring. It will cut off power to the motor to prevent any damage done to the internals of the AEG. Overall, this is a great addition to an AEG to increase the overall function as well as longevity without breaking the bank.
Specifications:
Manufacturer: Burst Wizard King Kong Super 3
Modes: Programmable
Package Includes: One (1) MOSFET System
Features:
Plug-And-Play or Hardwire ( Your Choice ! )
All the Burst Wizard King Kong Super 2 features
No Trigger Response Loss
ROF Reduction
Up to 3 rounds or x-rnd burst per trigger pull
Real Steel ROF 3-RND Burst & Fullauto MILSIM
Magazine Capacity & Change Time MILSIM
LiPo & LiFe Battery Low Voltage Protection
Any Battery Type From 7.2V to 16.5V
Smallest Size 1.3"L x 0.6" W x 0.4" H
- Specifications
- Manufacturer: Burst Wizard
- Color: Black, Red
- Material: Rubber, Silicone, Metal, Plastic
- Package Includes: One (1) MOSFET System
see 1 reviews
| Write a Review
verified buyer
verified buyer
J. RUSSELL
|
2015-02-17
Product Information:
Fantastic little device. Don't let the competitors fool you, this one's got it all and more. To be fair- mine is hardwired. It was a piece of cake to do (the BW3 has a big solder pad for the trigger wire, makes it easy) and the advantages are immediately apparent compared to leaving the motor current going through the trigger. Yes, the trigger response is much improved with a hardwire and the active braking makes followup shots very consistent. The burst feature is pretty flawless (took some fine tuning due to extremely high ROF in my case) and the fire select modes for Real Steel are very easy to use.
FYI, if you're going to do a hardwire, take the time and do it right. Don't leave the battery power going up to the switch then back down, simply go direct from the BW3 to the motor. I was able to touch up my gearbox enough to permit 2x12ga and 2x24ga wires to pass through without getting snagged on anything (is quite a squeeze though!). My Burst Wizard is feeding a Tienly GT45000 from a Matrix 25c 4000mAh 11.1v LiPo.
Pros:
Multiple fire modes
Real Steel
Piston cyclic control (preload, active braking)
Very fast trigger response
LiPo safety detection
Fault protection
Cons:
Would be nice if the power wires didn't exit on the same side of the BW3. It's a bit funky bending them back over the mosfet in the buffer tube and makes it harder for someone to use certain configurations of nunchuck batteries.
Fantastic little device. Don't let the competitors fool you, this one's got it all and more. To be fair- mine is hardwired. It was a piece of cake to do (the BW3 has a big solder pad for the trigger wire, makes it easy) and the advantages are immediately apparent compared to leaving the motor current going through the trigger. Yes, the trigger response is much improved with a hardwire and the active braking makes followup shots very consistent. The burst feature is pretty flawless (took some fine tuning due to extremely high ROF in my case) and the fire select modes for Real Steel are very easy to use.
FYI, if you're going to do a hardwire, take the time and do it right. Don't leave the battery power going up to the switch then back down, simply go direct from the BW3 to the motor. I was able to touch up my gearbox enough to permit 2x12ga and 2x24ga wires to pass through without getting snagged on anything (is quite a squeeze though!). My Burst Wizard is feeding a Tienly GT45000 from a Matrix 25c 4000mAh 11.1v LiPo.
Pros:
Multiple fire modes
Real Steel
Piston cyclic control (preload, active braking)
Very fast trigger response
LiPo safety detection
Fault protection
Cons:
Would be nice if the power wires didn't exit on the same side of the BW3. It's a bit funky bending them back over the mosfet in the buffer tube and makes it harder for someone to use certain configurations of nunchuck batteries.
|
|
2v3
what does the 3 do compared to two like other than the features of the 2 what does the three have that the two does not
2444 days ago carter b
0
0
(I have this same question)
Staff Answer:
Yes 2444 days ago 0
0
|
1 answers 1 asked |
|
|
wil it protect against a 11.1 lipo if i dont hard wire it
if i just pllug it in will it protect a gainst a 11.1 lipo
2444 days ago carter b
0
0
(I have this same question)
Staff Answer:
It will be able to handle an 11.1 LiPO battery. 2444 days ago 0
0
|
1 answers 1 asked |
|
|
battery
does a nimh battery work with this ?
3000 days ago Brenan H
0
0
(I have this same question)
Staff Answer:
It should be compatible with most airsoft gun builds. 2439 days ago 0
0
|
1 answers 1 asked |
|
|
m249
Will this work with my A&K m249? I would like 3 round burst along with full auto ?
3022 days ago matt d
0
0
(I have this same question)
Staff Answer:
It should work 3021 days ago 0
0
|
1 answers 1 asked |
|
|
can i make my gun shoot safe-semi-semi with the mosfet?
safe-semi-semi
3378 days ago Jacob O
0
0
(I have this same question)
Staff Answer:
The mosfet should be able to alter how many BB's are shot on the Auto Selector. 3377 days ago 0
0
safe-semi-semi
3378 days ago Jacob O
0
0
(I have this same question)
Staff Answer:
The mosfet should be able to alter how many BB's are shot on the Auto Selector. 3377 days ago 0
0
|
2 answers 1 asked |
|
|
Krytac spr
Will this work in a krytac spr or do I need to the the already installed mosfet out?
3453 days ago Will S
0
0
(I have this same question)
Staff Answer:
It should work 3452 days ago 0
0
|
1 answers 1 asked |
|
|
deans
Does the wizard 3 come with deans connectors
3504 days ago Dolores R
0
0
(I have this same question)
Staff Answer:
No. 3452 days ago 0
0
|
1 answers 1 asked |
|
|
Should you leave the fuse in the gun and still use this or remove the fuse?
In using this I blew my first ever fuse after ten years of playing.
3509 days ago Eric G
0
0
(I have this same question)
Staff Answer:
You can do either or. Both will work either way. 3454 days ago 0
0
|
1 answers 1 asked |
|
|
Amperage Limits | 0 answers 1 asked |
|
|
Lancer tactical ak74u Lipo protection
Will this allow me to use a tenergy 11.1 Lipo without destroying my gun
3634 days ago Abdullah G
0
0
(I have this same question)
Staff Answer:
No, it will not 100% protect the gun 3629 days ago 0
0
|
1 answers 1 asked |
|
|
lipo
Will this protect my trigger contacts from getting burned out from a 11.1 lipo?
3646 days ago Howard E
0
0
(I have this same question)
Staff Answer:
It will help protect them 3644 days ago 0
0
|
1 answers 1 asked |
|
|
Super 2 v. Super 3
Whats the differences between the price?
3674 days ago Anthony B
0
1
(I have this same question)
Staff Answer:
The Super 3 has more features 3673 days ago 0
0
|
1 answers 1 asked |
|
|
CA90TR
Will it fit in a classic army CA90TR
3724 days ago Cool G
0
0
(I have this same question)
Staff Answer:
Most likely not 3722 days ago 0
0
|
1 answers 1 asked |
Search Tags: Mosfet Electrical Burst Plug & Play And Easy Installation Adjustable Magazine Delay AEG Pre Cocking PRecocking
People who bought this item also purchased:
